diff --git a/stm32_bootloader.md b/stm32_bootloader.md
index 7dd761f..0ed277f 100644
--- a/stm32_bootloader.md
+++ b/stm32_bootloader.md
@@ -1,9 +1,6 @@
-# STM32 Bootloader
-
-The code for the PX4 bootloader is available from the Github [Bootloader](https://github.com/px4/bootloader) repository.
-
-## Supported Boards
-
+# STM32 引导程序
+ 用于加载 PX4的引导程序可以从GitHub的[Bootloader](https://github.com/px4/bootloader)库中获得。
+## 支持的硬件
   * FMUv1 (PX4FMU, STM32F4)
   * FMUv2 (Pixhawk 1, STM32F4)
   * FMUv3 (Pixhawk 2, STM32F4)
@@ -11,29 +8,19 @@ The code for the PX4 bootloader is available from the Github [Bootloader](https:
   * FMUv5 (Pixhawk 4, STM32F7)
   * TAPv1 (TBA, STM32F4)
   * ASCv1 (TBA, STM32F4)
-
-## Building the Bootloader
-
+##  编译引导程序
 ```bash
 git clone https://github.com/PX4/Bootloader.git
 cd Bootloader
 make
 ```
-
-After this step a range of elf files for all supported boards are present in the Bootloader directory.
-
-## Flashing the Bootloader
-
-> IMPORTANT: The right power sequence is critical for some boards to allow JTAG / SWD access. Follow these steps exactly as described. The instructions below are valid for a Blackmagic / Dronecode probe. Other JTAG probes will need different but similar steps. Developers attempting to flash the bootloader should have the required knowledge. If you do not know how to do this you probably should reconsider if you really need to change anything about the bootloader.
-
-  * Disconnect the JTAG cable
-  * Connect the USB power cable
-  * Connect the JTAG cable
-
-### Black Magic / Dronecode Probe
-
-#### Using the right serial port
-
+运行make后，编译产生一系列可执行文件（格式为elf）并保存在Bootloader文件下，所得可执行文件支持所有PX4硬件。
+## 烧写引导程序
+>重要信息：对于一些允许JTAG/SWD的飞控板必须保证正确的上电顺序。请严格按照以下步骤完成。以下说明适用于Blackmagic / Dronecode仿真。其他JTAG仿真不同于前面两个，但步骤类似。试图刷写bootloader的编程人员应该具备这些知识。如果你不知道知道这些，你可能真的应该考虑，你是否真的需要修改bootloader引导加载程序。
+  * 断开JTAG cable
+  * 连接USB电源cable
+  * 连接JTAG cable
+#### 使用正确的串口
   * On LINUX: ```/dev/serial/by-id/usb-Black_Sphere_XXX-if00```
   * On MAC OS: Make sure to use the cu.xxx port, not the tty.xxx port: ```tar ext /dev/tty.usbmodemDDEasdf```
 
@@ -49,17 +36,11 @@ arm-none-eabi-gdb
         Transfer rate: 17 KB/sec, 828 bytes/write.
   (gdb) kill
 ```
-
 ### J-Link
-
-These instructions are for the [J-Link GDB server](https://www.segger.com/jlink-gdb-server.html).
-
-#### Prerequisites
-
-[Download the J-Link software](https://www.segger.com/downloads/jlink#) from the Segger website and install it according to their instructions.
-
-#### Run the JLink GDB server
-
+J-Link相关说明看[J-Link GDB server](https://www.segger.com/jlink-gdb-server.html).
+#### 前提条件
+[下载 J-Link 软件](https://www.segger.com/downloads/jlink#)并按照Segger说明安装。
+#### 运行JLink GDB服务
 FMUv1:
 ```bash
 JLinkGDBServer -select USB=0 -device STM32F405RG -if SWD-DP -speed 20000
@@ -69,29 +50,28 @@ AeroFC:
 ```bash
 JLinkGDBServer -select USB=0 -device STM32F429AI -if SWD-DP -speed 20000
 ```
-
-#### Connect GDB
-
+#### 链接GDB
 ```bash
 arm-none-eabi-gdb
   (gdb) tar ext :2331
   (gdb) load aerofcv1_bl.elf
 ```
+### 故障排除
+运行命令时，如果提示上述命令没有被找到，可能是你没有使用Black magic或者软件已经过期。此时，请先升级on-probe软件。
 
-### Troubleshooting
+如果提示下方错误消息：
 
-If any of the commands above are not found, you are either not using a Blackmagic probe or its software is outdated. Upgrade the on-probe software first.
-
-If this error message occurs:
 ```Error erasing flash with vFlashErase packet```
 
 Disconnect the target (while leaving JTAG connected) and run 
 
+断开连接（保持JTAG连接状态）并运行下列命令：
+
 ```bash
 mon tpwr disable
 swdp_scan
 attach 1
 load tapv1_bl.elf
 ```
-This will disable target powering and attempt another flash cycle.
 
+此时将断开飞控板电源并尝试再次写入。