PowerWalker__VI_1500_CSW_IEC

PowerWalker/PowerWalker__VI_1500_CSW_IEC__nutdrv_qx__2.8.1__01.dev

@@ -0,0 +1,88 @@
+# Please add if relevant: DEVICE:URL:REPORT: 
+# Please add if relevant: DEVICE:URL:VENDOR: https://powerwalker.com/de/produkt/10121124/
+
+# Please add comments for humans here and perhaps raise concerns about the data points,
+# see https://networkupstools.org/ddl/#devseq-files for comment-tag syntax
+# strip sensitive data (passwords, SNMP community, serial number, IP address, host name...)
+# and post as a pull request to https://github.com/networkupstools/nut-ddl/
+# DEVICE:COMMENT:
+# Device dump generated by ./nut-ddl-dump.sh on Thu, 02 Apr 2026 21:19:57 +0000
+# DEVICE:EOC
+
+# :; upsc POWER
+battery.charge: 100
+battery.voltage: 27.7
+battery.voltage.high: 26.00
+battery.voltage.low: 20.80
+battery.voltage.nominal: 24.0
+device.type: ups
+driver.debug: 0
+driver.flag.allow_killpower: 0
+driver.name: nutdrv_qx
+driver.parameter.pollfreq: 30
+driver.parameter.pollinterval: 2
+driver.parameter.port: auto
+driver.parameter.product: HID UPS
+driver.parameter.productid: 5161
+driver.parameter.synchronous: auto
+driver.parameter.vendorid: 0665
+driver.state: quiet
+driver.version: 2.8.1
+driver.version.data: Voltronic-QS 0.09
+driver.version.internal: 0.36
+driver.version.usb: libusb-1.0.27 (API: 0x100010a)
+input.voltage: 236.0
+input.voltage.fault: 0.0
+output.current.nominal: 6.0
+output.frequency: 50.0
+output.frequency.nominal: 50
+output.voltage: 236.0
+output.voltage.nominal: 230
+ups.beeper.status: enabled
+ups.delay.shutdown: 30
+ups.delay.start: 180
+ups.firmware.aux: PM-H
+ups.load: 0
+ups.productid: 5161
+ups.status: OL
+ups.type: offline / line interactive
+ups.vendorid: 0665
+
+# DEVICE:COMMENT-BLOCK:FIXME:UPSRW: POWER
+# [driver.debug]
+# Current debug verbosity level of the driver program
+# Type: NUMBER
+# Value: 0
+#
+# [driver.flag.allow_killpower]
+# Safety flip-switch to allow the driver daemon to send UPS shutdown command (accessible via driver.killpower)
+# Type: NUMBER
+# Value: 0
+#
+# [ups.delay.shutdown]
+# Interval to wait after shutdown with delay command (seconds)
+# Type: RANGE NUMBER
+# Option: "12-540" SELECTED
+#
+# [ups.delay.start]
+# Interval to wait before (re)starting the load (seconds)
+# Type: RANGE NUMBER
+# Option: "60-599940" SELECTED
+# DEVICE:EOC
+
+# DEVICE:COMMENT-BLOCK:FIXME:UPSCMD: POWER
+# Instant commands supported on UPS [POWER]:
+#
+# beeper.toggle - Toggle the UPS beeper
+# driver.killpower - Tell the driver daemon to initiate UPS shutdown; should be unlocked with driver.flag.allow_killpower option or variable setting
+# driver.reload - Reload running driver configuration from the file system (only works for changes in some options)
+# driver.reload-or-error - Reload running driver configuration from the file system (only works for changes in some options); return an error if something changed and could not be applied live (so the caller can restart it with new options)
+# driver.reload-or-exit - Reload running driver configuration from the file system (only works for changes in some options); exit the running driver if something changed and could not be applied live (so service management framework can restart it with new options)
+# load.off - Turn off the load immediately
+# load.on - Turn on the load immediately
+# shutdown.return - Turn off the load and return when power is back
+# shutdown.stayoff - Turn off the load and remain off
+# shutdown.stop - Stop a shutdown in progress
+# test.battery.start.quick - Start a quick battery test
+# DEVICE:EOC
+